Not to be fixed
Created: Mar 7, 2013
Updated: Feb 23, 2018
Resolved Date: Feb 22, 2018
Previous ID: LIN5-5020, LIN6-2851
Found In Version: 6.0
Severity: Standard
Applicable for: Wind River Linux 6
Component/s: BSP - Async
mmc0: Hardware doesn't report any support voltages.
sdhci platform registration failed
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
oprofile: using arm/armv7-ca9
TCP: cubic registered
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
Registering the dns_resolver key type
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 0
Registering SWP/SWPB emulation handler
kmemleak: Kernel memory leak detector initialized
kmemleak: Automatic memory scanning thread started
console [netcon0] enabled
netconsole: network logging started
/work/board/xilinx_zynq_dvd28-standard/bitbake_build/tmp/work/xilinx_zynq-wrs-linux-gnueabi/linux-windriver-3.4-r0/linux/drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
GEM: lp->tx_bd c0866000 lp->tx_bd_dma 3eff2000 lp->tx_skb befdd000
GEM: lp->rx_bd c0864000 lp->rx_bd_dma 3eff1000 lp->rx_skb befdd400
GEM: MAC 0x2adad87a, 0x00003256, 7a:d8:da:2a:56:32
GEM: phydev bef71400, phydev->phy_id 0x1410cc2, phydev->addr 0x17
eth0, phy_addr 0x17, phy_id 0x01410cc2
eth0, attach [Marvell 88E1111] phy driver
Sending DHCP requests ., OK
IP-Config: Got DHCP answer from 10.0.2.2, my address is 10.0.2.15
IP-Config: Complete:
device=eth0, addr=10.0.2.15, mask=255.255.255.0, gw=10.0.2.2
host=10.0.2.15, domain=, nis-domain=(none)
bootserver=10.0.2.2, rootserver=10.0.2.2, rootpath=
md: Waiting for all devices to be available before autodetect
md: If you don't use raid, use raid=noautodetect
md: Autodetecting RAID arrays.
md: Scanned 0 and added 0 devices.
md: autorun ...
md: ... autorun DONE.
Waiting for root device /dev/mmcblk0...
eth0: link up (1000/FULL)
N
1) build kernel
cdc/fast_prod/wrlinux501/dvd_install/lx28_12sp-async/wrlinux-5/wrlinux/configure --enable-board=xilinx_zynq --enable-rootfs=glibc_std --enable-jobs=5 --enable-parallel-pkgbuilds=5 --enable-test=yes --with-layer=/work/wr-testing/bts/,/work/wr-testing/kts --with-template=feature/qemu-linaro --enable-bootimage=ext3 --enable-kernel=standard+cfg/fs/flash_fs.scc --with-rcpl-version=auto
2) run qemu-system-arm
./host-cross/usr/bin/qemu-system-arm -m 1024 -nographic -smp 2 -M xilinx-zynq-a9 -serial null -serial mon:stdio -kernel ../xilinx_zynq_dvd28-standard/bitbake_build/tmp/work/xilinx_zynq-wrs-linux-gnueabi/linux-windriver-3.4-r0/linux-xilinx-zynq-standard-build/arch/arm/boot/uImage -dtb export/xilinx-zynq-zynq-zc702-qemu-sd.dtb-WR5.0.1.0_standard -sd export/xilinx-zynq-glibc-std-standard-dist.ext3
