Fixed
Created: Jul 29, 2014
Updated: Dec 3, 2018
Resolved Date: Aug 25, 2014
Found In Version: 6.0
Fix Version: 6.0.0.11
Severity: Standard
Applicable for: Wind River Linux 6
Component/s: BSP - Async
10G net card can't detect on xlp8xx board.
-------------------
root@localhost:~# bash check_10GbE_nic.sh -u
Up all 10GbE NIC
l3cam mask :0 0x767f7640
l3cam even 0 : 0x950800
l3cam odd 0 : 0x30881000
Enabling parser for nae node 0 naeid 0
rx config 0x43391181
root@localhost:~# ifconfig
eth0 Link encap:Ethernet HWaddr 00:15:17:d7:37:4c
inet addr:128.224.178.48 Bcast:128.224.179.255 Mask:255.255.254.0
inet6 addr: fe80::215:17ff:fed7:374c/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:25355 errors:0 dropped:0 overruns:0 frame:0
TX packets:11981 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:29663402 (28.2 MiB) TX bytes:1806492 (1.7 MiB)
Interrupt:19 Memory:d0000000-d0020000
eth1 Link encap:Ethernet HWaddr 00:0f:30:20:0c:9d
inet6 addr: fe80::20f:30ff:fe20:c9d/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:5 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:418 (418.0 B)
eth2 Link encap:Ethernet HWaddr 00:0f:30:20:0c:9e
inet6 addr: fe80::20f:30ff:fe20:c9e/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:4 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:324 (324.0 B)
eth3 Link encap:Ethernet HWaddr 00:0f:30:20:0c:9f
inet6 addr: fe80::20f:30ff:fe20:c9f/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:4 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:324 (324.0 B)
eth4 Link encap:Ethernet HWaddr 00:0f:30:20:0c:a0
inet6 addr: fe80::20f:30ff:fe20:ca0/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:3 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:250 (250.0 B)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:8 errors:0 dropped:0 overruns:0 frame:0
TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:560 (560.0 B) TX bytes:560 (560.0 B)
root@localhost:~# ethtool eth4
Settings for eth4:
Supported ports: [ FIBRE ]
Supported link modes: 10000baseT/Full
Supported pause frame use: No
Supports auto-negotiation: No
Advertised link modes: 10000baseT/Full
Advertised pause frame use: No
Advertised auto-negotiation: No
Speed: 10000Mb/s
Duplex: Full
Port: FIBRE
PHYAD: 3
Transceiver: internal
Auto-negotiation: off
Current message level: 0x00000000 (0)
Link detected: no
root@localhost:~# ethtool eth3
Settings for eth3:
Supported ports: [ FIBRE ]
Supported link modes: 10000baseT/Full
Supported pause frame use: No
Supports auto-negotiation: No
Advertised link modes: 10000baseT/Full
Advertised pause frame use: No
Advertised auto-negotiation: No
Speed: 10000Mb/s
Duplex: Full
Port: FIBRE
PHYAD: 2
Transceiver: internal
Auto-negotiation: off
Current message level: 0x00000000 (0)
Link detected: no
root@localhost:~# ethtool eth2
Settings for eth2:
Supported ports: [ FIBRE ]
Supported link modes: 10000baseT/Full
Supported pause frame use: No
Supports auto-negotiation: No
Advertised link modes: 10000baseT/Full
Advertised pause frame use: No
Advertised auto-negotiation: No
Speed: 10000Mb/s
Duplex: Full
Port: FIBRE
PHYAD: 1
Transceiver: internal
Auto-negotiation: off
Current message level: 0x00000000 (0)
Link detected: no
root@localhost:~# ethtool eth1
Settings for eth1:
Supported ports: [ FIBRE ]
Supported link modes: 10000baseT/Full
Supported pause frame use: No
Supports auto-negotiation: No
Advertised link modes: 10000baseT/Full
Advertised pause frame use: No
Advertised auto-negotiation: No
Speed: 10000Mb/s
Duplex: Full
Port: FIBRE
PHYAD: 0
Transceiver: internal
Auto-negotiation: off
Current message level: 0x00000000 (0)
Link detected: no
root@localhost:~#
1) configure --enable-board=bcm-xlp --enable-kernel=standard --enable-rootfs=glibc-std --enable-test=yes --with-layer=/runtime/wr-testing/ltp,/runtime/wr-testing/kts-test,/runtime/wr-testing/bts --with-template=feature/kts-basic,feature/kts-extended,feature/kts-cgl --enable-parallel-pkgbuilds=24 --enable-jobs=24
2) deploy images.
3) insert 10G network card.
4) startup the boards (two xlp8xx boards, 21053 and 21054)
5) Check the 10G NIC interfaces status and check the connection status.
Check the logs and nic interface status.
