Fixed
Created: Jan 24, 2014
Updated: Dec 3, 2018
Resolved Date: Mar 4, 2014
Found In Version: 6.0
Fix Version: 6.0.0.4
Severity: Standard
Applicable for: Wind River Linux 6
Component/s: BSP
Problem Description
======================
suspend-to-disk (PowerManagement/disk) does not work properly.
1) It consumed long time to suspend to disk.
2) Console was lost after resuming from disk.
Expected Behavior
======================
run case normally
Observed Behavior
======================
None
Logs(Key error logs)
======================
root@p2020ds:~#
root@p2020ds:~# uname -a
Linux p2020ds 3.10.19-WR6.0.0.0_standard #1 SMP PREEMPT Tue Jan 21 14:25:23 CST 2014 ppc GNU/Linux
root@p2020ds:~#
root@p2020ds:~# mmc0: Timeout waiting for hardware interrupt.
mmc0: Timeout waiting for hardware interrupt.
root@p2020ds:~#
root@p2020ds:~# mkswap /dev/sda2
mkswap: /dev/sda2: warning: don't erase bootbits sectors
(dos partition table detected). Use -f to force.
Setting up swapspace version 1, size = 1048572 KiB
no label, UUID=7f0783ec-6559-4821-8687-246a5feaaabf
root@p2020ds:~#
root@p2020ds:~#
root@p2020ds:~# swapon /dev/sda2
Adding 1048572k swap on /dev/sda2. Priority:-1 extents:1 across:1048572k
root@p2020ds:~# mmc0: Timeout waiting for hardware interrupt.
root@p2020ds:~#
root@p2020ds:~# echo disk > /sys/power/state
mmc0: Timeout waiting for hardware interrupt.
mmc0: Timeout waiting for hardware interrupt.
mmc0: Timeout waiting for hardware interrupt.
mmc0: Timeout waiting for hardware interrupt.
mmc0: Timeout waiting for hardware interrupt.
mmc0: Timeout waiting for hardware interrupt.
mmc0: Timeout waiting for hardware interrupt.
mmc0: Timeout waiting for hardware interrupt.
^C^C^C^C^Ccmmc0: Timeout waiting for hardware interrupt.
mmc0: Timeout waiting for hardware interrupt.
mmc0: Timeout waiting for hardware interrupt.
mmc0: Timeout waiting for hardware interrupt.
mmc0: Timeout waiting for hardware interrupt.
mmc0: Timeout waiting for hardware interrupt.
mmc0: Timeout waiting for hardware interrupt.
mmc0: Timeout waiting for hardware interrupt.
mmc0: Timeout waiting for hardware interrupt.
mmc0: Timeout waiting for hardware interrupt.
mmc0: Timeout waiting for hardware interrupt.
mmc0: Timeout waiting for hardware interrupt.
mmc0: Timeout waiting for hardware interrupt.
mmc0: Timeout waiting for hardware interrupt.
mmc0: Timeout waiting for hardware interrupt.
mmc0: Timeout waiting for hardware interrupt.
mmc0: Timeout waiting for hardware interrupt.
mmc0: Timeout waiting for hardware interrupt.
mmc0: Timeout waiting for hardware interrupt.
mmc0: Timeout waiting for hardware interrupt.
mmc0: Timeout waiting for hardware interrupt.
mmc0: Timeout waiting for hardware interrupt.
mmc0: Timeout waiting for hardware interrupt.
mmc0: Timeout waiting for hardware interrupt.
mmc0: Timeout waiting for hardware interrupt.
mmc0: Timeout waiting for hardware interrupt.
mmc0: Timeout waiting for hardware interrupt.
mmc0: Timeout waiting for hardware interrupt.
mmc0: Timeout waiting for hardware interrupt.
mmc0: Timeout waiting for hardware interrupt.
mmc0: Timeout waiting for hardware interrupt.
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.01 seconds) done.
PM: Preallocating image memory... done (allocated 19086 pages)
PM: Allocated 76344 kbytes in 0.25 seconds (305.37 MB/s)
Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
Suspending console(s) (use no_console_suspend to debug)
PM: freeze of devices complete after 3.450 msecs
PM: late freeze of devices complete after 0.616 msecs
PM: noirq freeze of devices complete after 0.857 msecs
Disabling non-boot CPUs ...
Cannot set affinity for irq 37
PM: Creating hibernation image:
PM: Need to copy 18651 pages
PM: Hibernation image created (18651 pages copied)
Enabling non-boot CPUs ...
CPU1 is up
PM: noirq thaw of devices complete after 0.513 msecs
PM: early thaw of devices complete after 0.356 msecs
fsl-lbc ffe05000.localbus: Chip select error: LTESR 0x00080000
ata1: SATA link down (SStatus 0 SControl 300)
ata4: SATA link down (SStatus 0 SControl 300)
ata2: SATA link down (SStatus 0 SControl 300)
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: configured for UDMA/133
PM: thaw of devices complete after 525.072 msecs
PM: Using 1 thread(s) for compression.
PM: Compressing and saving image data (18670 pages)...
PM: Image saving progress: 0%
PM: Image saving progress: 10%
PM: Image saving progress: 20%
PM: Image saving progress: 30%
PM: Image saving progress: 40%
PM: Image saving progress: 50%
PM: Image saving progress: 60%
PM: Image saving progress: 70%
PM: Image saving progress: 80%
PM: Image saving progress: 90%
PM: Image saving done.
PM: Wrote 74680 kbytes in 1.11 seconds (67.27 MB/s)
PM: S|
sd 2:0:0:0: [sda] Synchronizing SCSI cache
sd 2:0:0:0: [sda] Stopping disk
Power down.
System Halted, OK to turn off power
Reboot:
========
U-Boot 2013.10-00006-g877bcdc-dirty (Nov 01 2013 - 14:56:01)
CPU0: P2020E, Version: 1.0, (0x80ea0010)
Core: e500, Version: 4.0, (0x80211040)
Clock Configuration:
CPU0:1199.988 MHz, CPU1:1199.988 MHz,
CCB:599.994 MHz,
DDR:399.996 MHz (799.992 MT/s data rate) (Asynchronous), LBC:37.500 MHz
L1: D-cache 32 KiB enabled
I-cache 32 KiB enabled
Board: P2020DS Sys ID: 0x16, Sys Ver: 0x02, FPGA Ver: 0x03, vBank: 1
I2C: ready
SPI: ready
DRAM: Detected UDIMM EBJ21EE8BAFA-AE-E
2 GiB (DDR3, 64-bit, CL=6, ECC off)
DDR Chip-Select Interleaving Mode: CS0+CS1
Testing 0x00000000 - 0x7fffffff
Remap DDR
POST memory PASSED
Flash: 128 MiB
L2: 512 KiB enabled
SRIO1: disabled
SRIO2: disabled
NAND: 0 MiB
MMC: FSL_SDHC: 0
EEPROM: NXID v0
PCIe1: Root Complex of Slot 2, no link, regs @ 0xffe0a000
PCIe1: Bus 00 - 00
PCIe2: Root Complex of ULI, x1, regs @ 0xffe09000
02:00.0 - 10b9:5249 - Bridge device
03:1c.0 - 10b9:5237 - Serial bus controller
03:1c.1 - 10b9:5237 - Serial bus controller
03:1c.2 - 10b9:5237 - Serial bus controller
03:1c.3 - 10b9:5239 - Serial bus controller
03:1e.0 - 10b9:1575 - Bridge device
03:1e.1 - 10b9:7101 - Bridge device
03:1f.0 - 10b9:5229 - Mass storage controller
03:1f.1 - 10b9:5288 - Mass storage controller
PCIe2: Bus 01 - 03
PCIe3: Root Complex of Slot 1, no link, regs @ 0xffe08000
PCIe3: Bus 04 - 04
In: serial
Out: serial
Err: serial
SCSI: SATA link 0 timeout.
SATA link 1 timeout.
Target spinup took 0 ms.
SATA link 3 timeout.
AHCI 0001.0000 32 slots 4 ports 3 Gbps 0xf impl IDE mode
flags: ncq ilck pm led clo pmp pio slum part
scanning bus for devices...
Device 0: (2:0) Vendor: ATA Prod.: Rev:
Type: Hard Disk
Capacity: not available
Found 1 device(s).
Net: eTSEC1 [PRIME], eTSEC2, eTSEC3
Hit any key to stop autoboot: 0
=>
=> printenv othbootargs
othbootargs=resume=/dev/sda2
=> printenv nfsboot
nfsboot=setenv bootargs root=/dev/nfs rw nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off console=$consoledev,$baudrate $othbootargs;tftp $loadaddr $bootfile;tftp $fdtaddr $fdtfile;bootm $loadaddr - $fdtaddr
=> printenv bootcmd
bootcmd=run nfsboot
=> boot
Speed: 100, full duplex
Using eTSEC1 device
TFTP from server 128.224.165.20; our IP address is 128.224.165.58
Filename 'vlm-boards/17560/kernel'.
Load address: 0x1000000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#######################################################
3.2 MiB/s
done
Bytes transferred = 4623955 (468e53 hex)
Speed: 100, full duplex
Using eTSEC1 device
TFTP from server 128.224.165.20; our IP address is 128.224.165.58
Filename 'vlm-boards/17560/dtb'.
Load address: 0xc00000
Loading: ##
1.2 MiB/s
done
Bytes transferred = 16715 (414b hex)
WARNING: adjusting available memory to 30000000
## Booting kernel from Legacy Image at 01000000 ...
Image Name: Linux-3.10.19-WR6.0.0.0_standard
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 4623891 Bytes = 4.4 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 00c00000
Booting using the fdt blob at 0xc00000
Uncompressing Kernel Image ... OK
Loading Device Tree to 03ff8000, end 03fff14a ... OK
WARNING: could not find compatible node fsl-usb2-mph or fsl-usb2-dr: FDT_ERR_NOTFOUND.
Using P2020 DS machine description
Only using first contiguous memory region
Memory CAM mapping: 256/256/256 Mb, residual: 1280Mb
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Initializing cgroup subsys cpuacct
Linux version 3.10.19-WR6.0.0.0_standard (gcc version 4.8.1 (Wind River Linux Sourcery CodeBench 4.8-24) ) #1 SMP PREEMPT Tue Jan 21 14:25:23 CST 2014
CPU maps initialized for 1 thread per core
bootconsole [udbg0] enabled
setup_arch: bootmem
mpc85xx_ds_setup_arch()
MPC85xx DS board from Freescale Semiconductor
arch: exit
Zone ranges:
DMA [mem 0x00000000-0x2fffffff]
Normal empty
HighMem [mem 0x30000000-0x7fffffff]
Movable zone start for each node
Early memory node ranges
node 0: [mem 0x00000000-0x7fffffff]
MMU: Allocated 1088 bytes of context maps for 255 contexts
PERCPU: Embedded 8 pages/cpu @c1a20000 s11872 r8192 d12704 u32768
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 522752
Kernel command line: root=/dev/nfs rw nfsroot=128.224.165.20:/export/pxeboot/vlm-boards/17560/rootfs ip=128.224.165.58:128.224.165.20:128.224.165.1:255.255.254.0:p2020ds:eth0:off console=ttyS0,115200 resume=/dev/sda2
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Sorting __ex_table...
allocated 4194304 bytes of page_cgroup
please try 'cgroup_disable=memory' option if you don't want memory cgroups
Memory: 1999360k/2097152k available (9172k kernel code, 97792k reserved, 404k data, 720k bss, 408k init)
Kernel virtual memory layout:
* 0xfffbf000..0xfffff000 : fixmap
* 0xffc00000..0xffe00000 : highmem PTEs
* 0xffbfd000..0xffc00000 : early ioremap
* 0xf1000000..0xffbfd000 : vmalloc & ioremap
SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Preemptible hierarchical RCU implementation.
NR_IRQS:512 nr_irqs:512 16
mpic: Setting up MPIC " OpenPIC " version 1.2 at ffe40000, max 2 CPUs
mpic: ISU size: 256, shift: 8, mask: ff
mpic: Initializing for 256 sources
i8259 legacy interrupt controller initialized
clocksource: timebase mult[d555e12] shift[24] registered
Console: colour dummy device 80x25
pid_max: default: 32768 minimum: 301
Security Framework initialized
Mount-cache hash table entries: 512
Initializing cgroup subsys debug
Initializing cgroup subsys memory
Initializing cgroup subsys devices
Initializing cgroup subsys freezer
Initializing cgroup subsys net_cls
Initializing cgroup subsys blkio
ftrace: allocating 22625 entries in 67 pages
mpic: requesting IPIs...
e500 family performance monitor hardware support registered
Brought up 2 CPUs
devtmpfs: initialized
xor: measuring software checksum speed
8regs : 1450.000 MB/sec
8regs_prefetch: 1211.000 MB/sec
32regs : 1445.000 MB/sec
32regs_prefetch: 1243.000 MB/sec
xor: using function: 8regs (1450.000 MB/sec)
NET: Registered protocol family 16
Found FSL PCI host bridge at 0x00000000ffe08000. Firmware bus number: 0->0
PCI host bridge /pcie@ffe08000 ranges:
MEM 0x0000000080000000..0x000000009fffffff -> 0x0000000080000000
IO 0x00000000ffc00000..0x00000000ffc0ffff -> 0x0000000000000000
/pcie@ffe08000: PCICSRBAR @ 0xfff00000
Found FSL PCI host bridge at 0x00000000ffe09000. Firmware bus number: 0->2
PCI host bridge /pcie@ffe09000 (primary) ranges:
MEM 0x00000000a0000000..0x00000000bfffffff -> 0x00000000a0000000
IO 0x00000000ffc10000..0x00000000ffc1ffff -> 0x0000000000000000
/pcie@ffe09000: PCICSRBAR @ 0xfff00000
Found FSL PCI host bridge at 0x00000000ffe0a000. Firmware bus number: 0->0
PCI host bridge /pcie@ffe0a000 ranges:
MEM 0x00000000c0000000..0x00000000dfffffff -> 0x00000000c0000000
IO 0x00000000ffc20000..0x00000000ffc2ffff -> 0x0000000000000000
/pcie@ffe0a000: PCICSRBAR @ 0xfff00000
PCI: Probing PCI hardware
fsl-pci ffe08000.pcie: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [io 0xfffe0000-0xfffeffff] (bus address [0x0000-0xffff])
pci_bus 0000:00: root bus resource [mem 0x80000000-0x9fffffff]
pci_bus 0000:00: root bus resource [bus 00-ff]
pci 0000:00:00.0: ignoring class 0x0b2000 (doesn't match header type 01)
pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
pci 0000:00:00.0: PCI bridge to [bus 01-ff]
fsl-pci ffe09000.pcie: PCI host bridge to bus 0001:02
pci_bus 0001:02: root bus resource [io 0x0000-0xffff]
pci_bus 0001:02: root bus resource [mem 0xa0000000-0xbfffffff]
pci_bus 0001:02: root bus resource [bus 02-ff]
pci 0001:02:00.0: ignoring class 0x0b2000 (doesn't match header type 01)
pci 0001:02:00.0: Primary bus is hard wired to 0
pci 0001:02:00.0: bridge configuration invalid ([bus 01-02]), reconfiguring
pci 0001:03:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
pci 0001:02:00.0: PCI bridge to [bus 03-ff]
pci 0001:03:00.0: bridge configuration invalid ([bus 02-02]), reconfiguring
pci 0001:03:00.0: PCI bridge to [bus 04-ff] (subtractive decode)
fsl-pci ffe0a000.pcie: PCI host bridge to bus 0002:05
pci_bus 0002:05: root bus resource [io 0x20000-0x2ffff] (bus address [0x0000-0xffff])
pci_bus 0002:05: root bus resource [mem 0xc0000000-0xdfffffff]
pci_bus 0002:05: root bus resource [bus 05-ff]
pci 0002:05:00.0: ignoring class 0x0b2000 (doesn't match header type 01)
pci 0002:05:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
pci 0002:05:00.0: PCI bridge to [bus 06-ff]
pci 0000:00:00.0: PCI bridge to [bus 01]
pci 0000:00:00.0: bridge window [io 0xfffe0000-0xfffeffff]
pci 0000:00:00.0: bridge window [mem 0x80000000-0x9fffffff]
pci 0001:03:00.0: PCI bridge to [bus 04]
pci 0001:03:00.0: bridge window [io 0x1000-0x1fff]
pci 0001:03:00.0: bridge window [mem 0xa0000000-0xa00fffff]
pci 0001:02:00.0: PCI bridge to [bus 03-04]
pci 0001:02:00.0: bridge window [io 0x0000-0xffff]
pci 0001:02:00.0: bridge window [mem 0xa0000000-0xbfffffff]
pci 0002:05:00.0: PCI bridge to [bus 06]
pci 0002:05:00.0: bridge window [io 0x20000-0x2ffff]
pci 0002:05:00.0: bridge window [mem 0xc0000000-0xdfffffff]
pci 0000:00:00.0: enabling device (0106 -> 0107)
pci 0001:02:00.0: enabling device (0106 -> 0107)
pci 0002:05:00.0: enabling device (0106 -> 0107)
fsl-l2ctlr ffe20000.l2-cache-controller: Entire L2 as cache, provide valid sram address and size
fsl-l2ctlr: probe of ffe20000.l2-cache-controller failed with error -22
bio: create slab <bio-0> at 0
raid6: int32x1 183 MB/s
raid6: int32x2 301 MB/s
raid6: int32x4 427 MB/s
raid6: int32x8 363 MB/s
raid6: using algorithm int32x4 (427 MB/s)
raid6: using intx1 recovery algorithm
Freescale Elo / Elo Plus DMA driver
fsl-elo-dma ffe0c300.dma: #0 (fsl,eloplus-dma-channel), irq 76
fsl-elo-dma ffe0c300.dma: #1 (fsl,eloplus-dma-channel), irq 77
fsl-elo-dma ffe0c300.dma: #2 (fsl,eloplus-dma-channel), irq 78
fsl-elo-dma ffe0c300.dma: #3 (fsl,eloplus-dma-channel), irq 79
fsl-elo-dma ffe21300.dma: #0 (fsl,eloplus-dma-channel), irq 21
fsl-elo-dma ffe21300.dma: #1 (fsl,eloplus-dma-channel), irq 22
fsl-elo-dma ffe21300.dma: #2 (fsl,eloplus-dma-channel), irq 23
fsl-elo-dma ffe21300.dma: #3 (fsl,eloplus-dma-channel), irq 24
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
nfc: nfc_init: NFC Core ver 0.1
NET: Registered protocol family 39
Switching to clocksource timebase
NET: Registered protocol family 2
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 4, 98304 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP: reno registered
UDP hash table entries: 512 (order: 2, 16384 bytes)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
Freescale PMC driver
bounce pool size: 64 pages
HugeTLB registered 4 MB page size, pre-allocated 0 pages
HugeTLB registered 16 MB page size, pre-allocated 0 pages
HugeTLB registered 64 MB page size, pre-allocated 0 pages
HugeTLB registered 256 MB page size, pre-allocated 0 pages
HugeTLB registered 1 GB page size, pre-allocated 0 pages
NFS: Registering the id_resolver key type
Key type id_resolver registered
Key type id_legacy registered
bio: create slab <bio-1> at 1
Btrfs loaded
aufs 3.10-20130819
msgmni has been set to 1473
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
serial8250.0: ttyS0 at MMIO 0xffe04500 (irq = 42) is a 16550A
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
serial8250.0: ttyS1 at MMIO 0xffe04600 (irq = 42) is a 16550A
brd: module loaded
ahci 0001:04:1f.1: AHCI 0001.0000 32 slots 4 ports 3 Gbps 0xf impl SATA mode
ahci 0001:04:1f.1: flags: ncq sntf ilck pm led clo pmp pio slum part
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
ata1: SATA max UDMA/133 abar m1024@0xa0003400 port 0xa0003500 irq 37
ata2: SATA max UDMA/133 abar m1024@0xa0003400 port 0xa0003580 irq 37
ata3: SATA max UDMA/133 abar m1024@0xa0003400 port 0xa0003600 irq 37
ata4: SATA max UDMA/133 abar m1024@0xa0003400 port 0xa0003680 irq 37
e8000000.nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x002801
Amd/Fujitsu Extended Query Table at 0x0040
Amd/Fujitsu Extended Query version 1.3.
number of CFI chips: 1
7 ofpart partitions found on MTD device e8000000.nor
Creating 7 MTD partitions on "e8000000.nor":
0x000000000000-0x000003000000 : "ramdisk"
0x000003000000-0x000003e00000 : "diagnostic"
0x000003e00000-0x000004000000 : "dink"
0x000004000000-0x000004400000 : "kernel"
0x000004400000-0x000007f00000 : "jffs2"
0x000007f00000-0x000007f80000 : "dtb"
0x000007f80000-0x000008000000 : "u-boot"
NAND device: Manufacturer ID: 0xec, Chip ID: 0xd5 (Samsung NAND 2GiB 3,3V 8-bit), 2048MiB, page size: 4096, OOB size: 128
fsl,elbc-fcm-nand ffa00000.nand: fsl_elbc_init: page size 4096 is not supported
fsl,elbc-fcm-nand: probe of ffa00000.nand failed with error -1
No NAND device found
No NAND device found
No NAND device found
fsl_espi ffe07000.spi: master is unqueued, this is deprecated
m25p80 spi32766.0: s25sl12801 (16384 Kbytes)
4 ofpart partitions found on MTD device spi32766.0
Creating 4 MTD partitions on "spi32766.0":
0x000000000000-0x000000100000 : "u-boot-spi"
0x000000100000-0x000000600000 : "kernel-spi"
0x000000600000-0x000000700000 : "dtb-spi"
0x000000700000-0x000001000000 : "file system-spi"
fsl_espi ffe07000.spi: at 0xf107a000 (irq = 59)
libphy: Fixed MDIO Bus: probed
libphy: Freescale PowerQUICC MII Bus: probed
: cannot get PHY at address 28
: cannot get PHY at address 29
: cannot get PHY at address 17
libphy: Freescale PowerQUICC MII Bus: probed
libphy: Freescale PowerQUICC MII Bus: probed
fsl-gianfar ffe24000.ethernet eth0: mac: 00:04:9f:00:d8:fb
fsl-gianfar ffe24000.ethernet eth0: Running with NAPI enabled
fsl-gianfar ffe24000.ethernet eth0: RX BD ring size for Q[0]: 256
fsl-gianfar ffe24000.ethernet eth0: TX BD ring size for Q[0]: 256
fsl-gianfar ffe25000.ethernet eth1: mac: 00:04:9f:00:d8:fc
fsl-gianfar ffe25000.ethernet eth1: Running with NAPI enabled
fsl-gianfar ffe25000.ethernet eth1: RX BD ring size for Q[0]: 256
fsl-gianfar ffe25000.ethernet eth1: TX BD ring size for Q[0]: 256
fsl-gianfar ffe26000.ethernet eth2: mac: 00:04:9f:00:d8:fd
fsl-gianfar ffe26000.ethernet eth2: Running with NAPI enabled
fsl-gianfar ffe26000.ethernet eth2: RX BD ring size for Q[0]: 256
fsl-gianfar ffe26000.ethernet eth2: TX BD ring size for Q[0]: 256
pps pps0: new PPS source ptp0
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
fsl-ehci fsl-ehci.0: irq 28, io mem 0xffe22000
fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
usbcore: registered new interface driver usb-storage
i8042: No controller found
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
mpc-i2c ffe03000.i2c: timeout 1000000 us
at24 0-0050: 8192 byte 24c64 EEPROM, writable, 1 bytes/write
at24 0-0051: 8192 byte 24c64 EEPROM, writable, 1 bytes/write
mpc-i2c ffe03100.i2c: timeout 1000000 us
rtc-ds1307 1-0068: rtc core: registered ds1339 as rtc0
ata4: SATA link down (SStatus 0 SControl 300)
ata1: SATA link down (SStatus 0 SControl 300)
ata2: SATA link down (SStatus 0 SControl 300)
zl6100 1-0011: Device ID ZL2006-002-FE11
zl6100 1-0011: Device mismatch: Configured zl6100, detected zl2006
booke_wdt: powerpc book-e watchdog driver loaded
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
md: multipath personality registered for level -4
md: faulty personality registered for level -5
device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
ata3.00: ATA-8: Hitachi HDP725016GLA380, GMBOA52A, max UDMA/133
ata3.00: 312581808 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
ata3.00: configured for UDMA/133
mmc0: SDHCI controller on ffe2e000.sdhc [ffe2e000.sdhc] using DMA
scsi 2:0:0:0: Direct-Access ATA Hitachi HDP72501 GMBO PQ: 0 ANSI: 5
sd 2:0:0:0: Attached scsi generic sg0 type 0
sd 2:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2
sd 2:0:0:0: [sda] Attached SCSI disk
usb 1-1: new high-speed USB device number 2 using fsl-ehci
talitos ffe30000.crypto: hwrng
talitos ffe30000.crypto: max_xor_srcs 6
talitos ffe30000.crypto: fsl,sec3.1 algorithms registered in /proc/crypto
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
u32 classifier
Actions configured
TCP: cubic registered
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
Key type dns_resolver registered
Freezing user space processes ... (elapsed 0.00 seconds) done.
PM: Using 1 thread(s) for decompression.
PM: Loading and decompressing image data (18670 pages)...
usb-storage 1-1:1.0: USB Mass Storage device detected
scsi4 : usb-storage 1-1:1.0
PM: Image loading progress: 0%
PM: Image loading progress: 10%
PM: Image loading progress: 20%
PM: Image loading progress: 30%
PM: Image loading progress: 40%
PM: Image loading progress: 50%
PM: Image loading progress: 60%
PM: Image loading progress: 70%
PM: Image loading progress: 80%
PM: Image loading progress: 90%
scsi 4:0:0:0: Direct-Access Generic USB Flash Disk 8.07 PQ: 0 ANSI: 2
sd 4:0:0:0: Attached scsi generic sg1 type 0
sd 4:0:0:0: [sdb] 3883008 512-byte logical blocks: (1.98 GB/1.85 GiB)
sd 4:0:0:0: [sdb] Write Protect is off
sd 4:0:0:0: [sdb] No Caching mode page found
sd 4:0:0:0: [sdb] Assuming drive cache: write through
sd 4:0:0:0: [sdb] No Caching mode page found
sd 4:0:0:0: [sdb] Assuming drive cache: write through
PM: Image loading done.
PM: Read 74680 kbytes in 1.21 seconds (61.71 MB/s)
Suspending console(s) (use no_console_suspend to debug)
1. Config
/bsp-dev/git/wrlinux-x/wrlinux/configure --enable-jobs=8 --enable-parallel-pkgbuilds=8 --enable-kernel=standard --enable-rootfs=glibc-std --enable-board=fsl_p2020 --with-layer=/net/bsp-dev/git/wr-testing/5.0/wr-testing-60/bts --enable-test=yes
2. Test suspend to disk.
