Wind River Support Network

Description

Booting information:

cdns-ufshcd 4e84000.ufs: ufshcd_populate_vreg: Unable to find vdd-hba-supply regulator, assuming enabled

cdns-ufshcd 4e84000.ufs: ufshcd_populate_vreg: Unable to find vcc-supply regulator, assuming enabled

cdns-ufshcd 4e84000.ufs: ufshcd_populate_vreg: Unable to find vccq-supply regulator, assuming enabled

cdns-ufshcd 4e84000.ufs: ufshcd_populate_vreg: Unable to find vccq2-supply regulator, assuming enabled

scsi host0: ufshcd

cdns-ufshcd 4e84000.ufs: ufshcd_print_pwr_info:[RX, TX]: gear=[1, 1], lane[1, 1], pwr[SLOWAUTO_MODE, SLOWAUTO_MODE], rate = 0

cdns-ufshcd 4e84000.ufs: ufshcd_print_pwr_info:[RX, TX]: gear=[3, 3], lane[2, 2], pwr[FAST MODE, FAST MODE], rate = 2

davinci_mdio 46000f00.mdio: davinci mdio revision 9.7, bus freq 1000000

libphy: 46000f00.mdio: probed

cdns-ufshcd 4e84000.ufs: ufshcd_find_max_sup_active_icc_level: Regulator capability was not set, actvIccLevel=0

scsi 0:0:0:49488: Well-known LUN TOSHIBA THGAF8G8T23BAILB 0300 PQ: 0 ANSI: 6

davinci_mdio 46000f00.mdio: phy[0]: device 46000f00.mdio:00, driver TI DP83867

am65-cpsw-nuss 46000000.ethernet: initializing am65 cpsw nuss version 0x6BA00101, cpsw version 0x6BA80100 Ports: 2 quirks:00000000

am65-cpsw-nuss 46000000.ethernet: Failed to request tx dma channel -517

scsi 0:0:0:49476: Well-known LUN TOSHIBA THGAF8G8T23BAILB 0300 PQ: 0 ANSI: 6

am65-cpts 310d0000.cpts: CPTS ver 0x4e8a010a, freq:200000000, add_val:4 pps:0

cdns-ufshcd 4e84000.ufs: ufshcd_scsi_add_wlus: BOOT WLUN not found

rti-wdt 2200000.watchdog: heartbeat 60 sec

rti-wdt 2210000.watchdog: heartbeat 60 sec

Steps to Reproduce

1.     build a project

/lpg-build/cdc/fast_prod/WRLINUX_MASTER_WR/MASTER_WR_GIT/wrlinux-10/setup.sh --machines=ti-j72xx --distro wrlinux-graphics --dl-layers --accept-eula=yes

. ./environment-setup-x86_64-wrlinuxsdk-linux

. ./oe-init-build-env build_test

 

bitbake-layers add-layer /buildarea1/renfeiqu/master_wr/testcases/wr-testing/bts-dev/

 

echo "require templates/feature/bts/template.conf" >> conf/local.conf

 

echo BB_NUMBER_THREADS ?= \"24\" >> conf/local.conf

 

echo PARALLEL_MAKE ?= \"-j 24\" >> conf/local.conf

 

echo "WRTEMPLATE_append = \" feature/docker feature/target-toolchain \"" >> conf/local.conf

 

 

bitbake wrlinux-image-std-sato

 

2. boot up the board