Wind River Support Network

Description

1. Build project.
setup.sh --machines=xilinx-zynqmp --templates f --distro wrlinux --dl-layers --accept-eula=yes

. ./oe-init-build-env build;

bitbake wrlinux-image-glibc-std

2. Boot up the xilinx-zynqmp BSP ZCU102 target (28571)

3. Run the following commands on the target

/opt/wr-test/testcases/bts/bootcheck_error/runtest.sh
/opt/wr-test/testcases/bts/bootcheck_exception/runtest.sh

root@xilinx-zynqmp:/#dmesg
...
[ 2.487366] i2c i2c-0: Added multiplexed i2c bus 5
[ 2.490973] pca954x 0-0075: registered 4 multiplexed busses for I2C mux pca9544
[ 2.498632] at24 6-0054: 1024 byte 24c08 EEPROM, writable, 1 bytes/write
[ 2.504112] i2c i2c-1: Added multiplexed i2c bus 6
[ 2.507910] i2c i2c-7: of_i2c: modalias failure on /amba/i2c@ff030000/i2c-mux@74/i2c@1/clock-generator@36
[ 2.516246] i2c i2c-7: Failed to create I2C device for /amba/i2c@ff030000/i2c-mux@74/i2c@1/clock-generator@36
[ 2.525003] i2c i2c-1: Added multiplexed i2c bus 7
[ 2.530808] si570 8-005d: registered, current frequency 300000000 Hz
[ 2.535917] i2c i2c-1: Added multiplexed i2c bus 8
[ 2.541086] si570 9-005d: clock registration failed
[ 2.544764] si570: probe of 9-005d failed with error -17
[ 2.548819] i2c i2c-1: Added multiplexed i2c bus 9
[ 2.552627] i2c i2c-10: of_i2c: modalias failure on /amba/i2c@ff030000/i2c-mux@74/i2c@4/clock-generator@69
[ 2.561012] i2c i2c-10: Failed to create I2C device for /amba/i2c@ff030000/i2c-mux@74/i2c@4/clock-generator@69
[ 2.569777] i2c i2c-1: Added multiplexed i2c bus 10
[ 2.573663] i2c i2c-1: Added multiplexed i2c bus 11
[ 2.577575] i2c i2c-1: Added multiplexed i2c bus 12
[ 2.581479] i2c i2c-1: Added multiplexed i2c bus 13
[ 2.585070] pca954x 1-0074: registered 8 multiplexed busses for I2C switch pca9548
[ 2.591900] i2c i2c-1: Added multiplexed i2c bus 14
[ 2.595807] i2c i2c-1: Added multiplexed i2c bus 15
–
[ 2.705940] ina2xx 3-0042: power monitor ina226 (Rshunt = 5000 uOhm)
[ 2.711538] ina2xx 3-0043: power monitor ina226 (Rshunt = 5000 uOhm)
[ 2.717144] ina2xx 3-0044: power monitor ina226 (Rshunt = 5000 uOhm)
[ 2.722733] ina2xx 3-0045: power monitor ina226 (Rshunt = 5000 uOhm)
[ 2.728352] ina2xx 3-0046: power monitor ina226 (Rshunt = 5000 uOhm)
[ 2.733946] ina2xx 3-0047: power monitor ina226 (Rshunt = 5000 uOhm)
[ 2.739756] cdns-wdt fd4d0000.watchdog: Xilinx Watchdog Timer at (___ptrval___) with timeout 10s
[ 2.748071] device-mapper: ioctl: 4.40.0-ioctl (2019-01-18) initialised: dm-devel@redhat.com
[ 2.755554] EDAC MC: ECC not enabled
[ 2.758156] cpu cpu0: failed to get clock: -2
[ 2.761218] cpufreq-dt: probe of cpufreq-dt failed with error -2
[ 2.766903] sdhci: Secure Digital Host Controller Interface driver
[ 2.771771] sdhci: Copyright(c) Pierre Ossman
[ 2.774816] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.808085] mmc0: SDHCI controller on ff170000.mmc [ff170000.mmc] using ADMA 64-bit
[ 2.815699] usbcore: registered new interface driver usbhid
[ 2.819976] usbhid: USB HID core driver
[ 2.822799] u32 classifier
[ 2.824235] Actions configured
[ 2.827655] NET: Registered protocol family 10
[ 2.832237] Segment Routing with IPv6

Steps to Reproduce

1. Build project.
/lpg-build/cdc/fast_prod/WRL10_19/WRL10_19_GIT/wrlinux-10/setup.sh --machines=xilinx-zynqmp --templates feature/linux-yocto-dev feature/toolchain-next feature/userspace-next --distro wrlinux --dl-layers --accept-eula=yes 

. ./oe-init-build-env build; 

bitbake wrlinux-image-glibc-std

2. Boot up the xilinx-zynqmp BSP ZCU102 target (28571)

3. Run the following commands on the target 

# /opt/wr-test/testcases/bts/bootcheck_error/runtest.sh
# /opt/wr-test/testcases/bts/bootcheck_exception/runtest.sh